From planning to the manufacturing of hip prosthesis by additive manufacturing
DOI:
https://doi.org/10.17533/udea.rcm.n16a03Keywords:
additive manufacturing, hip prothesis, customization, designAbstract
Total hip arthroplasty is one of the most common surgical procedures worldwide in adult patients; This procedure involves the replacement of the hip with an implant whose objective is to restore mobility to the affected limb. The planning of the surgical intervention, as well as the design of the prosthesis are fundamental for the success of the implant. This paper presents a review of the planning, design and selection of a hip prosthesis, as well as the achievement of a personalized prosthesis that is currently possible thanks to additive manufacturing techniques.
Downloads
References
Kalaskar, Deepak M. (ed.). “3D printing in medicine”. Woodhead Publishing, 2017.
Brandt, Milan (ed.). “Laser additive manufacturing: materials, design, technologies, and applications”. Woodhead Publishing, 2016.
Cronskär, Marie. “On customization of orthopedic implants-from design and additive manufacturing to implementation”.2014. Tesis Doctoral. Kopieringen, Mid Sweden University.
Georgios Tsoulfas, Petros I. Bangeas, Jasjit Suri, “3D Printing: Applications in Medicine and Surgery”,Elsevier, 1a Ed., 2019.
Shapií, A., Sulaiman, R., Hasan, M. K., Prabuwono, A. S., & Kassim, A. Y. M. “Digital two dimensional (2D) implant design for pre-operative planning in Total hip Arthroplasty”. International Journal on Electrical Engineering and Informatics, 4(1), 67, 2012.
Shichman, I., Factor, S., Shaked, O., Morgan, S., Amzallag, N., Gold, A., et al. “Effects of surgeon experience and patient characteristics on accuracy of digital pre-operative planning in total hip arthroplasty”.International Orthopaedics, 1-6, 2020.
Eggli, S., Pisan, M., & Müller, M. E. “The value of preoperative planning for total hip arthroplasty”. The Journal of bone and joint surgery. British volume, 80(3), 382-390, 1998.
Bono, J. V. “Digital templating in total hip arthroplasty”. JBJS, 86 (suppl_2), 118-122, 2004.
Bayne, C. O., Krosin, M., & Barber, T. C. “Evaluation of the accuracy and use of x-ray markers in digital templating for total hip arthroplasty”.The Journal of arthroplasty, 24(3), 407-413, 2009.
Della Valle, A. G., Comba, F., Taveras, N., & Salvati, E. A. “The utility and precision of analogue and digital preoperative planning for total hip arthroplasty”.International orthopaedics, 32(3), 289-294, 2008.
Holzer, L. A., Scholler, G., Wagner, S., Friesenbichler, J., Maurer-Ertl, W., & Leithner, A. “The accuracy of digital templating in uncemented total hip arthroplasty”. Archives of Orthopaedic and Trauma Surgery, 139(2), 263-268, 2017.
Kosashvili, Y., Shasha, N., Olschewski, E., Safir, O., White, L., Gross, A., & Backstein, D. “Digital versus conventional templating techniques in preoperative planning for total hip arthroplasty”. Canadian Journal of Surgery, 52(1), 6, 2009.
Konyves, A., & Bannister, G. C. “The importance of leg length discrepancy after total hip arthroplasty”.The Journal of bone and joint surgery. British volume, 87(2), 155-157.
Sariali, E., Mauprivez, R., Khiami, F., Pascal-Mousselard, H., & Catonné, Y. “Accuracy of the preoperative planning for cementless total hip arthroplasty. A randomised comparison between three-dimensional computerised planning and conventional templating”. Orthopaedics & Traumatology: Surgery & Research, 98(2), 151-158, 2012.
Knafo, Y., Houfani, F., Zaharia, B., Egrise, F., Clerc-Urmès, I., & Mainard, D. “Value of 3D Preoperative planning for primary total hip arthroplasty based on biplanar weightbearing radiographs”. BioMed Research International, 2019.
Salem, H. S., Marchand, K. B., Ehiorobo, J. O., Tarazi, J. M., Matzko, C. N., Sodhi, N., et al. “Benefits of CT Scanning for the Management of Hip Arthritis and Arthroplasty”. Surgical Technology International, 36, 2020.
Kobayashi, H., Cech, A., Kase, M., Pagenstart, G., Carrillon, Y., O’Loughlin, P. F., et al. “Pre-operative templating in THA. Part II: a CT-based strategy to correct architectural hip deformities”.Archives of Orthopaedic and Trauma Surgery, 1-12, 2020.
Yi, L. H., Li, R., Zhu, Z. Y., Bai, C. W., Tang, J. L., Zhao, F. C., et al. “Anatomical study based on 3D-CT image reconstruction of the hip rotation center and femoral offset in a Chinese population: preoperative implications in total hip arthroplasty”. Surgical and Radiologic Anatomy, 41(1), 117-124. 2019.
Carter, L. W., Stovall, D. O., & Young, T. R. “Determination of accuracy of preoperative templating of noncemented femoral prostheses”.The Journal of arthroplasty, 10(4), 507-513, 2005.
Knight, J. L., & Atwater, R. D. “Preoperative planning for total hip arthroplasty: quantitating its utility and precision”. The Journal of arthroplasty, 7, 403-409, 1992.
Ahmad R, Sharma V, Sandhu H, Bishay M. “Leg length discrepancy in total hip arthroplasty with the use of cemented and uncemented femoral stems. A prospective radiological study”. Hip Int; 19:264—7, 2009.
Sariali, E., & Knaffo, Y. “Three-dimensional analysis of the proximal anterior femoral flare and torsion. Anatomic bases for metaphyseally fixed short stems design”.International Orthopaedics, 41(10), 2017.
Zeng, C., Xing, W., Wu, Z., Huang, H., & Huang, W. “A combination of three-dimensional printing and computer-assisted virtual surgical procedure for preoperativeplanning of acetabular fracture reduction”.Injury, 47(10), 2223-2227, 2016.
Ganguli, A., Pagan-Diaz, G. J., Grant, L., Cvetkovic, C., Bramlet, M., Vozenilek, J., et al. “3D printing for preoperative planning and surgical training: a review”.Biomedical microdevices, 20(3), 65, 2018.
Tsoulfas G., Petros I. Bangeas, Jasjit Suri, “3D Printing: Applications in Medicine and Surgery”. Elsevier, 1a Ed., 2019.
Lorna J.G., Michael F.A. “Cellular Solids. Structure and Properties”(Cambridge Solid State Science Series). Cambridge University Press. 2-26, 1999.
Schoen, A. H. “Infinite Periodic Minimal Surfaces Without Self-Intersection”.National Aeronautics and Space Administration (NASA) Tech, Washington, DC (Note no. D-5541), 1970.
Hussein, A., Hao, L., Yan, C. et al. “Advanced lattice support structures for metal additive manufacturing”.Journal of Materials Processing Technology, 213. Pp 1019-1026, 2013.
Schileo, E., Dall ́Ara, E., et al.“An accurate estimation of bone density improves the accuracy of subject-specific finite element models”. Journal of Biomechanics, 41. Pp 2483-2491, 2008.
Kaneko, T.S. Bell, J.S., Pejcic, M.R., et al. “Mechanical properties, density and quantitative CT scan data of trabecular bone with and without metastases”.J. Biomech, 37(4). Pp 523-530, 2004.
Deepak MK. “3D Printing in Medicine”. Elsevier. Chapters 1, 2. 1-42, 2017.
Duan B., Wang M., Zhou WY., Cheung WL., Li ZY., Lu WW. “Three-dimensional nanocomposite scaffolds fabricated via selective laser sintering for bone tissue engineering”.Acta Biomater. 6(12): 4495-505, 2010.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 Revista Colombiana de Materiales
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
