Experimental study of flat plate cooling using draft induced by a submerged radial jet

Argemiro Palencia-Diaz; Cesar  Barraza-Botet; Antonio José Bula-Silvera

doi:10.17533/udea.redin.n83a08

Authors

Argemiro Palencia-Diaz Autonomous University of the Caribbean https://orcid.org/0000-0003-4947-5659
Cesar Barraza-Botet University de Michigan https://orcid.org/0000-0002-0094-1172
Antonio José Bula-Silvera University of the North https://orcid.org/0000-0002-3816-6423

DOI:

https://doi.org/10.17533/udea.redin.n83a08

Keywords:

impingement, microchip cooling, boundary layer reattachment

Abstract

An experimental research has been conducted for evaluating heat transfer in a modified configuration of a submerged radial jet, so it was possible to extract the fluid directly under the nozzle, looking for an improvement in the heat transfer rate. The experiments were conducted for the following ranges of the phenomenon governing parameters: 16 mm nozzle diameter, nozzle to plate distance ranging from 10 mm to 20 mm, Reynolds number ranging between 10,000 and 20,000, and heat density of 10.2 – 13.6 kW/m2. The heat transfer coefficient as well as Nusselt number for the different conditions under study were estimated using the temperature distribution obtained from a data acquisition device and appropriated post-processing. The use of fluid extraction through induced draft generated a significant increase in heat transfer in the area under the nozzle, obtaining values ranging from 290 up to 1500 W/m2.°C.

|Abstract

= 214 veces | PDF

= 212 veces|

Downloads

Download data is not yet available.

Author Biographies

Argemiro Palencia-Diaz, Autonomous University of the Caribbean

Assistant Professor. Department of Mechanical Engineering.

Cesar Barraza-Botet, University de Michigan

Mechanical Engineering Department.

Antonio José Bula-Silvera, University of the North

Professor. Department of Mechanical Engineering.

References

R. H. Page, L. Hadden, and C. Ostowari, “Theory for Radial Jet Reattachment Flow,” AIAA Journal, vol. 27, no. 11, pp. 1500-1505, 1989.

S. Yao, Y. Guo, N. Jiang, and J. Liu, “An experimental study of a turbulent jet impinging on a flat surface,” International Journal of Heat and Mass Transfer, vol. 83, pp. 820-832, 2015.

S. V. Alekseenko, A. V. Bilsky, V. M. Dulin, and D. M. Markovich, “Experimental study of an impinging jet with different swirl rates,” International Journal of Heat and Fluid Flow, vol. 28, no. 6, pp. 1340-1359, 2007.

G. M. Carlomagno and A. Ianiro, “Thermo-fluid-dynamics of submerged jets impinging at short nozzle-to-plate distance: A review,” Experimental Thermal and Fluid Science, vol. 58, pp. 15-35, 2014.

M. R. Pais, J. E. Leland, W. S. Chang, and L. C. Chow, “Single-Phase Heat Transfer Characteristics of Submerged Jet Impingement Cooling Using JP-5,” in 4th Intersociety Conference on Thermal Phenomena in Electronic Systems (I-THERM), Washington, D. C., USA, 1994, pp. 178-183.

S. V. Garimella and B. Nenaydykh, “Nozzle-geometry effects in liquid Jet impingement heat transfer,” International Journal of Heat Mass Transfer, vol. 39, no. 14, pp. 2915-2923, 1996.

J. Wu, J. Seyed, and R. H. Page, “Heat transfer and combustion characteristics of an array of radial jet reattachment flames,” Combustion and Flame, vol. 125, no. 1-2, pp. 955-964, 2001.

H. G. Lee, H. S. Yoon, and M. Y. Ha, “A numerical investigation on the fluid flow and heat transfer in the confined impinging slot jet in the low Reynolds number region for different channel heights,” International Journal of Heat and Mass Transfer, vol. 51, no. 15-16, pp. 4055-4068, 2008.

M. M. Rahman, A. J. Bula, and J. E. Leland, “Conjugate Heat Transfer During Free Jet Impingement of High Prandtl Number Fluid,” Numerical Heat Transfer, Part B: Fundamentals, vol. 36, no. 2, pp. 139-162, 1999.

A. J. Bula, M. M. Rahman, and J. E. Leland, “Numerical Modeling of Conjugate Heat Transfer during Impingement of Free Liquid Jet Issuing from a Slot Nozzle,” Numerical Heat transfer, Part A: Applications, vol. 38, no. 1, pp. 45-66. 2000.

A. J. Bula, M. M. Rahman, and J. E. Leland, “Axial Steady Jet Impinging over a Flat Disk with Discrete Heat Sources,” International Journal of Heat and Fluid Flow, vol. 21, no. 1, pp. 11-21. 2000.

M. M. Rahman, A. J. Bula, and J. E. Leland, “Analysis of Transient Conjugate Heat Transfer to a Free Impinging Jet,” Journal of Thermophysics and Heat Transfer, vol. 14, no. 3, pp. 330-339, 2000.

A. Tay, X. Hong, and Y. Cheng, “Cooling of Electronic Components with Free Jet Impingement Boiling,” in 8th Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems (ITHERM), San Diego, USA, 2002, pp. 387-394.

J. B. Baonga, H. Louahlia, and M. Imbert, “Experimental study of the hydrodynamic and heat transfer of free liquid jet impinging a flat circular heated disk,” Applied Thermal Engineering, vol. 26, no. 11-12, pp. 1125-1138, 2006.

D. W. Zhou and C. F. Ma, “Radial heat transfer behavior of impinging submerged circular jets,” International Journal of Heat and Mass Transfer, vol. 49, no. 9-10, pp. 1719-1722, 2006.

M. Cely, A. Bula, and A. Ramos, “Experimental Study of Transient Heat Transfer Process in a Submerged Radial Jet,” in ASME International Mechanical Engineering Congress and Exposition, Chicago, USA, 2006, pp. 563-568.

J. S. Furlow and D. L. James, “Convective heat transfer characteristics from combined mechanical and supply pulsed radial reattaching jets,” International Journal of Heat and Fluid Flow, vol. 28, no. 1, pp. 178-190, 2007.

T. S. O’Donovan and D. B. Murray, “Jet impingement heat transfer – Part I: Mean and root-mean-square heat transfer and velocity distributions,” International Journal of Heat and Mass Transfer, vol. 50, no. 17-18, pp. 3291–3301, 2007.

J. C. Duda, F. D. Lagor, and A. S. Fleischer, “A flow visualization study of the development of vortex structures in a round jet impinging on a flat plate and a cylindrical pedestal,” Experimental Thermal and Fluid Science, vol. 32, no. 8, pp. 1754-1758, 2008.

N. Celik and H. Eren, “Heat transfer due to impinging co-axial jets and the jets’ fluid flow characteristics,” Experimental Thermal and Fluid Science, vol. 33, no. 4, pp. 715-727, 2009.

M. F. Koseoglu and S. Baskaya, “The role of jet inlet geometry in impinging jet heat transfer, modeling and experiments,” International Journal of Thermal Sciences, vol. 49, no. 8, pp. 1417-1426, 2010.